Several secure payment methods
Fast shipping
Telephone support
-
Our products
-
Flexible ducting hose
-
Pipes
-
Bends
-
Branches
-
Cleaning
-
Cone
-
Container connection
-
Detection equipment
-
Endplate
-
High vacuum cleaning system
-
Installlation accessories
-
Jetcap
-
Manual dampers
-
Pneumatic sliding dampers
-
Rings
-
Sealing material
-
Silencers
-
Spare parts dampers
-
Suction manifold
-
Trouser pipe
-
- Our projects
- Our advices
- Our good deals
- Configurator
- FAQ
- Contact us
Antiwear reduction
Connector for flexible hoses
Connector for machine
Anti-static ducting hoses, 0,4 mm
Anti-static ducting hoses, 0,6mm
Ducting hoses, 0,9 mm
Flexibel hose 0.7 mm special CNC
Torsion compensation
Wire for PU flexible
Pipes 0,50 m
Pipes 1,00 m
Pipes 2,00 m
Pipes with access door
Telescopic pipes
Pressed
Segmented
Branch at 30°
Branch at 45°
Branch plate 30°
Branch Plate 45°
Branch plate at 30°
Branch plate at 45°
Nozzle with flex. connection
Wall sweep up with gate
Level detector
Branch pipes
Cleaning system
Cones
End plates
Flap valve for vacuum cleaning
Flexible hose for high vacuum
Steel pipe, galvanised, 3 m long
High vacuum unit
Hose reel
Pipe coupling 100 mm
Pipe coupling 150 & 200 mm
Pipe coupling 65 mm
Pipe support HV
Steel bends
Trousers 45°
Bushings for threaded rods
Cantilever arm
Rails / U-profiles
Support
Threaded rods
Galvanized manual throttle valve
Manual pressed sliding damper, no seal
Manual slide dampers for pneumatic
Sliding damper with balance
Standard manual galvanized sliding dampe
Tight sliding damper with seal
Galvanized Flange
Quick lock ring with seal
Quick-release clamps with seals
Bolt en nut Ø 8 x 35 mm
Slim ring
Legs for wall bracket
Wall/ceilling brackets
Wide ring
Silencers 0,50 m
Silencers 1,0 m
Silencers 2,0 m
Coil 24 VAC - 24 VDC - 230 VAC
Cylinder
Electric valve
Polyurethane ducting hoses
Trouser at 30°
Trouser at 45°
- Flexible ducting hose
- Pipes
- Bends
- Branches
- Cleaning
- Cone
- Container connection
- Detection equipment
- Endplate
- High vacuum cleaning system
- Installlation accessories
- Jetcap
- Manual dampers
- Pneumatic sliding dampers
- Rings
- Sealing material
- Silencers
- Spare parts dampers
- Suction manifold
- Trouser pipe
Branch plates with a 30° angle for adapting your dust/chip extraction system to your needs
These branch plates have an angle of 30° to enable you to easily add another section to your existing extraction system. Carefully select the two diameters, i.e. the one to be attached to the existing ductwork, and then the one chosen for the extension of your extraction system.
The advantage of using this part is that you do not have to dismantle the existing ductwork to add the ‘graft’. Simply place it where you want it, trace the opening to be made in the existing ductwork through the inside of the branch plate, cut the sheet metal, then fix the branch plate in place with self-drilling screws and/or silicone.
Multiple combinations of diameters are possible. Branch plates with other combinations of diameters are available on request. They are not always shown on the website.
Simply email us at info@ducomat.be and we will do our best to accommodate you.
Branch plates with a 30° angle for adapting your dust/chip extraction system to your needs
These branch plates have an angle of 30° to enable you to easily add another section to your existing extraction system. Carefully select the two diameters, i.e. the one to be attached to the existing ductwork, and then the one chosen for the extension of your extraction system.
The advantage of using this part is that you do not have to dismantle the existing ductwork to add the ‘graft’. Simply place it where you want it, trace the opening to be made in the existing ductwork through the inside of the branch plate, cut the sheet metal, then fix the branch plate in place with self-drilling screws and/or silicone.
Multiple combinations of diameters are possible. Branch plates with other combinations of diameters are available on request. They are not always shown on the website.
Simply email us at info@ducomat.be and we will do our best to accommodate you.
Branch plates with a 30° angle for adapting your dust/chip extraction system to your needs
These branch plates have an angle of 30° to enable you to easily add another section to your existing extraction system. Carefully select the two diameters, i.e. the one to be attached to the existing ductwork, and then the one chosen for the extension of your extraction system.
The advantage of using this part is that you do not have to dismantle the existing ductwork to add the ‘graft’. Simply place it where you want it, trace the opening to be made in the existing ductwork through the inside of the branch plate, cut the sheet metal, then fix the branch plate in place with self-drilling screws and/or silicone.
Multiple combinations of diameters are possible. Branch plates with other combinations of diameters are available on request. They are not always shown on the website.
Simply email us at info@ducomat.be and we will do our best to accommodate you.
Branch plates with a 30° angle for adapting your dust/chip extraction system to your needs
These branch plates have an angle of 30° to enable you to easily add another section to your existing extraction system. Carefully select the two diameters, i.e. the one to be attached to the existing ductwork, and then the one chosen for the extension of your extraction system.
The advantage of using this part is that you do not have to dismantle the existing ductwork to add the ‘graft’. Simply place it where you want it, trace the opening to be made in the existing ductwork through the inside of the branch plate, cut the sheet metal, then fix the branch plate in place with self-drilling screws and/or silicone.
Multiple combinations of diameters are possible. Branch plates with other combinations of diameters are available on request. They are not always shown on the website.
Simply email us at info@ducomat.be and we will do our best to accommodate you.
Product filters (106 products)
icon
Fast shipping
icon